1, The specification of the product including basic size information, electrical and mechanical properties.
| Basic size information |
| Termination Interface Style |
Crimp or compression |
| Processing methods |
E-stamping before tin-plated |
| Insulation O.D. |
2.50mm(Max) |
| Part No. |
C5080M-T-A or C5080M-T-B |
| Application |
Signal |
| Package |
7K/reel |
| |
| Electrical properties |
| Current Rating |
10A AC, DC |
| Voltage Rating |
250V AC, DC |
| Contact Resistance |
10mΩ Max |
| Insulation Resistance |
1000mΩ min |
| Withstanding Voltage |
1500V AC/minute |
| |
| Mechanical properties |
| Temperature range |
-25℃ to 85 ℃ |
| Other information please kindly check the following picture. |
2, Related drawing and report
The following pictures are engineering drawing and testing report for your reference, wish these can help you to purchase the ideal and right parts from us. Thank you!
|
5. Mechanical Performance
| Test Description |
Procedure |
Requirement |
| 5-1 |
Actuator Insertion & Withdrawal Force |
Insert and withdraw connectors at the speed rate of 25±3mm / minute. |
Refer to paragraph 7 |
| 5-2 |
Crimping Pull Out Force |
Fix the crimped terminal, apply axial pull out force on the wire at the speed rat of 25±3mm / minute.(Based upon JIS C5402 6.8) |
AWG#14 |
11.0kgf (Min) |
| AWG#16 |
10.0kgf (Min) |
| AWG#18 |
9.0kgf (Min) |
| AWG#20 |
6.0kgf (Min) |
| AWG#22 |
4.0kgf (Min) |
| AWG#24 |
3.0kgf (Min) |
| 5-3 |
Terminal Insertion Force. |
Insert the crimped terminal into the housing. |
2.00kgf (Max.) |
| 5-4 |
Terminal/Housing Retention Force. |
Apply axial pull out force at the speed rate of 25±3mm / minute on the terminal assembled in the housing. |
3.00kgf (Min.) |
| 5-5 |
Pin Retention Force |
Apply axial push force at the speed rate of 25±3mm / minute |
2.0kgf (Min.) |
| 5-6 |
Durability |
When mated up to 50 cycles repeatedly by the rate of 10 cycle per minute. |
Contact Resistance 20mΩ (Max.) |
| 5-7 |
Vibration |
Amplitude: 1.5mm P-P
Sweep time: 10-55-10 Hz in 1 minute Duration: 2 hours in each X.Y.Z. axes.
(Based upon MIL-STD-202 Method 201A)
|
Appearance No Damage.
Contact Resistance 20mΩ (Max.)
Discontinuity 1 μsec.(Max.)
|
| 5-8 |
Physical Shock |
490m/s²｛50G｝,3 strokes in each X.Y.Z. axes. (Based upon JIS C0041/MIL-STD-202 Method 213B Cond. A) |
|
|
6. Environmental Performance And Others
| Test Description |
Procedure |
Requirement |
| 6-1 |
Temperature Rise |
Carrying rated current load.(Based upon UL 498) |
30℃(Max.) |
| 6-2 |
Heat Resistance |
85±2℃,96 hours (Based upon JIS C0021/MIL-STD-202 Method 108A Cond. A) |
Appearance No Damage.
Contact Resistance 20mΩ (Max.)
|
| 6-3 |
Cold Resistance |
-25±3℃,96 hours (Based upon JIS C0020) |
| 6-4 |
Humidity |
Temperature: 40±2℃
Relative Humidity : 90~95%
Duration: 96 hours
(Based upon JIS C0022/MIL-STD-202 Method 103B Cond. B)
|
Appearance No Damage.
Contact Resistance 20mΩ (Max.)
Insulation Resistance 100MΩ (Min.)
Dielectric Withstanding Voltage Must meet 4-3
|
| 6-5 |
Temperature Cycling |
5 cycles of:
a) -55℃ 30 minutes
b) +85℃ 30 minutes
(Based upon JIS C0025)
|
Appearance No Damage.
Contact Resistance 20mΩ (Max.)
|
| 6-6 |
Salt Spray |
Tin-plated 12 hours / Gold- plated 24 hours exposure to a salt spray from the 5±1% solution at 35±2℃. (Based upon JIS C0023/MIL-STD-202 Method 101D Cond. B) |
| 6-7 |
SO2 Gas |
24 hours exposure to 50±5ppm.
SO2 gas at 40±2℃.
|
| 6-8 |
NH3 Gas |
40 minutes exposure to NH3 gas evaporating from 28% Ammonia solution. |
| 6-9 |
Solderability |
Soldering Time: 5±0.5 sec.
Solder Temperature: 245±5℃
|
Solder Wetting 95% of immersed area must show no voids, pin holes |
| 6-10 |
Resistance to Soldering Heat |
Solder pot method
Soldering time: 10±0.5 sec.
Solder Temperature: 260±5℃
Solder iron method
Soldering Time: 5±0.5 sec.
Solder Temperature: 370℃ ~ 400℃
|
Appearance No Damage. |
7. Actuator Insertion/Withdrawal Force
[Unit : kgf]
| Circuits |
At Initial |
| Insertion (Max.) |
Withdrawal (Min.) |
| Single |
1.50 |
0.30 |
| 04 |
10.00 |
2.50 |
|
3, FAQ
MOQ:
If have stock, according to the smallest package.
If not, according to the produce MOQ.
R&D ability:ODM&OEM is avaiable. We also can help you design molds and produce products.
Delivery time:3 to 8 days according to your order amount.
Quality Control: Original connector or replace connector we'll be 100% inspected before dispatching.
Package:PE Bag or Nylon Bag with Carton or according to you
Company Type : Factory and trade integration more than 12-years connector mold design and produce experience.
Product Tags:
|
|
5.08mm ptich tin-plated brass material terminals Brass Contact wire crimp terminals Images
|
